Full service kit containing 1 x UFI oil filter, 1 x UFI air filter, 2 x NGK BP6ES spark plugs, 2 x condensers, 1 x set points, 2 x sump gaskets, 2 x rocker cover gaskets and all crush washers to complete a service on your bike.

Save time and hassle by ordering service oil kit OIA14001 with your service kit

Save £'s by buying everything in a service kit

For models with electronic ignition see SIA18002, if you have a deep sump you'll need an extra sump gasket (ENA14036). Oils and lubricants available separately. The oils you need are 1 x OIA11036 and 1 x OIA08194

 3 in stock

Replacement alternator rotor for Bosch systems

See ELA17400 for matching stator and TOA14008 for rotor removal tool. We recommend changing the timing cover oil seal ENA90428 when changing the rotor. Also fits Yamaha RD350, FZR1000 and 1000 Fazer. Note that new rotors may need energizing, see our faultfinder for details.

 1 in stock

Also fits Benelli 900 Sei (Series 2)

Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.

Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear

 1 in stock

 01738030 GU01738030 01 73 80 30
 0173 8030 0173.8030 01.73.80.30

Left hand Domino type switchgear with high and low beam, pass, indicator and horn switches. Same style switch as ELA01738

On most bikes this will not plug directly into the wiring loom, you will need to match the wires to your loom. An indication of wire colours is supplied with this switchgear. Supplied with 9 pin block connector. NB does not have lights off - park - on function, you need this to be on your RH switch (e.g. ELA01729 ) or run lights always on

 This part is available by special order, request a quote

Complete shallow bowl 190mm chrome headlight unit. Includes a pilot / parking light. A shallow bowl makes it especially suitable for mounting on Moto Guzzis underneath the instruments

Homologated for road use.

Supplied complete with H4 bulb, pilot light and four short wires (without connectors). This headlight will fit fairing cowling FAA99575 for Le Mans 1 conversions if trim strip is not fitted to inside edge of fairing. NB mounting holes will need drilling out to 10mm if fitting T3 type indicator stems

 Availability varies on this part, check availability

Fuel tank lock with two keys

 Sorry, this part is no longer available.

 14736856 GU14736856 14 73 68 56
 1473 6856 1473.6856 14.73.68.56

Complete round black headlight with chrome rim, complete with bulb and pilot light. Right hand dip non-UK spec.

This light will fit Le Mans Fairing FAA99575

 This part is available by special order, request a quote

Stainless steel fasteners kit for PHF and PHM carb models with sump extension.This kit contains nuts, bolts and washers for the following: rocker covers, timing cover, gearbox bell housing, alternator cover, gearbox rear cover, neutral switch, drive box to swingarm, starter motor, head studs, exhaust flanges, inlet manifolds and sump. Just what you need to brighten up your Guzzi and ensure nuts and bolts don't seize on your bike

This engine bolt kit contains appropriate M6, M8, M10 socket cap and hex head bolts, nuts and washers. 149 pieces. To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070). You may also require a replacement front engine bolt kit in stainless (SSA14450) or distributor screws (SSA05025 and SSA04008)

 More than 5 in stock

Stainless steel fasteners kit for VHB carb models with sump extension.This kit contains nuts, bolts and washers for the following: rocker covers, timing cover, gearbox bell housing, alternator cover, gearbox rear cover, neutral switch, drive box to swingarm, starter motor, head studs, exhaust flanges, inlet manifolds and sump. Just what you need to brighten up your Guzzi and ensure nuts and bolts don't seize on your bike

This engine bolt kit contains appropriate M6, M8, M10 socket cap and hex head bolts, nuts and washers. 149 pieces. To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070). You may also require a replacement front engine bolt kit in stainless (SSA14450) or distributor screws (SSA05025 and SSA04008)

 More than 5 in stock

Stainless steel fasteners kit for PHF and PHM carb models without sump extension.This kit contains nuts, bolts and washers for the following: distributor clamp, rocker covers, timing cover, gearbox bell housing, alternator cover, gearbox rear cover, neutral switch, drive box to swingarm, starter motor, head studs, exhaust flanges, inlet manifolds and sump. Just what you need to brighten up your Guzzi and ensure nuts and bolts don't seize on your bike

This engine bolt kit contains appropriate M6, M8, M10 socket cap and hex head bolts, nuts and washers. 149 pieces. To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070). You may also require a replacement front engine bolt kit in stainless (SSA14450) or distributor screws (SSA05025 and SSA04008)

 More than 5 in stock